日韩人妻中文无码一区二区七区_经典久久久久_最近手机中文字幕1页_亚洲大尺度无码无码专线_日韩精品 中文字幕 一区_国产色情老熟女NBA控卫之神

首頁 技術中心>帕金斯柴油機活塞和連桿組件維修的安裝方法

帕金斯柴油機活塞和連桿組件維修的安裝方法

2016/5/8 18:55:19

帕金斯柴油機活塞和連桿組件維修的安裝方法

Pistons and connecting rod assemblies

2800

To remove and to fit

Special requirements


Operation 4-


To remove

  Remove the cylinder head assembly, Operation -5.

2  Remove the oil pump, Operation 0.


Anti-seize compound


CV60890

  Remove the stiffener plate from the base of the crankc ase.

4  Remove the carbon ridge from the top inside surface of the cylinder liners.

5  Turn the crankshaft until two pistons are at bottom centre.

6  Remove the bolts (A) and the bearing caps. Push the connecting rods and pistons up until the rings are

free from the cylinder liners.

7 Withdraw carefully the pistons and connecting rods from the cylinder liners. Store the bearing caps with their

relev ant connecting rods.

8  Repeat steps  to 6 for the remainder of the pistons and connecting rods.


2800

To fit

  Apply clean engine oil to the piston rings, the connecting rod bearings and the cylinder liners.

2  Ensure that the piston ring gaps are set at 20 degree intervals to each other.

 Use the special tool (B), GE5000 for 2806 engines or GE50045 for 206 engines , to install the piston and

the connecting rod in the cylinder liner (B2). The connecting rod must be fitted with tab groove side of the big

end bearing at the opposite s ide to the camshaft. Proceed with care to ensure that the piston rings are not

damaged during the operation.

Caution: Bearing caps must be fitted to their original connecting rods,

4  Fit the bearing cap to the connecting rod. The cap must be fitted with its number on the same s ide as that

on the connecting rod and the number must be the same.

5  Apply anti-seize compound, CV60890, to the bolt threads. Install the bolts and bearing cap. Tighten each

bolt in the bearing cap to a torque of 90 +/- 8 Nm (66 +/- 6 lbf ft). Make a temporary mark on each bolt and the

bearing cap, then tighten each bolt by an additional 90 +/- 5 degrees.

6  Repeat steps  to 4 for the remainder of the pistons and connecting rods.

7  Fit the stiffener plate to the base of the crankcase.

8  Fit the oil pump, Operation 0.

9  Fit the cylinder head assembly, Operation -5.

4


2800

To dismantle and assemble

To dismantle

  Remove the pistons and connecting rod assemblies, Operation 4-.


Operation 4-2


2 Remove the big-end bearing shells (A5) from the connecting rod (A4) and connecting rod cap. If the bearings

are to be used again, make a note of the position where they were fitted.

  Remove the circlips (A).

4  Remove the gudgeon pin (A2) and separate the connecting rod and the piston crown from the piston.

5  Remove carefully the piston rings (A) from the piston crown and clean the piston ring grooves with a

suitable cleaning tool.

Special equipment is required to renew the small end bearing. If this operation becomes necessary, contact

your Perkins dealer.


2800

To assemble

  Check the gaps between the ends of the piston rings when the rings are inserted in a new liner. The rings

can also be c hecked by insertion in an unworn part of a used liner.

For the correct dimensions refer to Chapter 2, Specific ations.

2  Fit the spring of the oil control ring to its groove in the piston crown.

Note: The oil control ring must be fitted over the spring with the gap of the oil control ring at 80 degrees  from

the joint of the spring.

  Use a suitable piston ring expander to fit the oil control ring to its groove in the piston crown.

4 Fit the second (intermediate) piston ring with the side that has the identification "UP-2" toward the top of the

piston. Use a suitable piston ring expander.

5 Fit the first (top) piston ring with the side that has the identification "UP-" toward the top of the piston. Use

a suitable piston ring expander.

6  When all three piston rings have been fitted, adjust the position of the piston ring gaps so that they are

20 degrees apart.

7 Fit the piston crown into the piston skirt and insert the connec ting rod. Apply clean engine oil to the gudgeon

pin (A2) and install the pin. Fit the circlips (A). Ensure that the circlips are located fully in the grooves of the

piston.

8 Fit the big-end bearings to the connecting rod (A4) and connecting rod cap. If the original bearings are to be

used, ensure that they are fitted to their original positions.

Note: The tabs at back of the bearings must be located correctly  in the tab slots of the connec ting rod and

connecting rod cap.

9  Fit the pistons and connecting rod assemblies, Operation 4-.


帕金斯活塞環和軸承,帕金斯機油格,韓國大宇發電機配件,perkins起動機2873k059,帕金斯發電機ECM板價格,三凌柴油機起動馬達,帕金斯1104c p4ta發動機配件,北京威爾信發電機組配件,帕金斯機器配件哪賣,進口珀金斯發動機配件,perkins 2614b562皮帶,沃爾沃遍達TDW1641GE發動機配件,perkins 4006 氣門 ,perkins發電機p30E1濾清器,三菱發電機S12A2配件,帕金斯柴油發電機組配件,威爾信 P635E1配件,Perkins4008TAG 2的配件,Perkins 過濾器,三菱柴油發動機活塞環,六缸帕金斯發動機配件,無錫帕金斯1104d發動機配件,P110E英國威爾信350KW配件,帕金斯2645A747噴油器

免費熱線
400-100-8969???15088860848
機組銷售
0574-26871589? 15267810868
配件銷售
0574-26886646? 15706865167
維修熱線
0574-26871569  18658287286
手機端
微信公眾號
在線客服
主站蜘蛛池模板: 免费观看又黄又爽的视频 | 456亚洲| 最近在线更新8中文字幕免费 | 小娇乳H边走边欢1V1视频国产 | 宝贝好紧好爽再搔一点试视频 | 日本人妻出轨中文字幕 | 国产乱人 | SM免费人成虐网站 | 久久久综合九色合综国产精品 | 久久精品无码专区免费东京热 | 依依成人精品视频在线观看 | 亚洲日韩精品AV无码麻豆 | 大陆老熟女嗷嗷叫AV在线 | 亚洲中文字幕在线观看 | 亚洲VA中文字幕不卡无码 | 国产传媒在线免费观看 | 2018国产大陆天天弄 | 国产成人Av乱码免费观看 | 亚洲中文av一区二区三区 | 中国浓毛少妇毛茸茸 | 国产婷婷一区二区三区 | 91a在线观看 | 亚洲精品精华液一区二区 | 亚洲AV成人无码网站18禁在线播放 | 精品卡一卡二卡3卡高清乱码 | 9i看片成人免费 | 蜜臀性色AV免费 | 精品一卡2卡三卡4卡乱码仙踪林 | 亚洲AV无码潮喷在线观看 | 亚洲伊人久久综合成人网站 | 熟女视频一区二区在线观看 | 亚洲 欧美 日韩 国产综合 在线 | 99久久婷婷国产综合精品 | 四虎成人影院在线观看 | 日韩欧美不卡一卡二卡3卡四卡2021免费 | 国产又色又爽又黄的视频在线 | 1000部又爽又黄无遮挡的视频 | 阳茎伸入女人阳道视频免费 | 久久青青草原国产精品最新片 | 成人久 | 中文字幕在线日亚洲9 |